 |
|
首页 > 产品 > 2.4GHz 无线通信芯片 > A7192
A7192
产品选择指南
| General Description |
|
A7192 is a high power and low cost 2.4GHz ISM band transceiver. A7192 supports fast PLL settling time for frequency hopping system. For packet handling, A7192 has built-in separated (512 bytes) TX/RX FIFO for data buffering and burst transmission, auto-ack and auto-resend, CRC for error packet filtering, FEC (7,4 hamming code) for 1-bit data correction per code word, RSSI for clear channel assessment, thermal sensor to monitor relative temperature, data whitening for data encryption / decryption. In addition, A7192 has built-in AES128 co-processor (Advanced Encryption Standard) for advanced data encryption or decryption which consists of the transformation of a 128-bit block into an encrypted 128-bit block. Those functions are very easy to use while developing a wireless system. All features are integrated in a small QFN 4X4 24 pins package. A7192’s control registers are accessed via 3-wire or 4-wire SPI interface such as TX/RF FIFO, ID register, RSSI value, frequency hopping and calibration procedures. Another one is the unique Strobe command via SPI to control power saving mode (sleep, idle, standby), TX mode and RX mode. The other connections between A7192 and MCU are GIO1 and GIO2 (multi-function GPIO) to output A7192’s status so that MCU could use either polling or interrupt scheme for radio control. Overall, it is very easy to develop a wireless application by a MCU and A7192 because of its rich and easy-to-use features. |
Small size (QFN4X4, 24 pins).
Frequency band: 2400 ~ 2483.5MHz.
FSK/GFSK modulation.
Sleep current (3 uA).
RX current consumption: 23mA (AGC on).
TX current consumption: 100mA (17dBm).
On chip regulator, support input voltage 3 ~ 3.6 V.
Data rate 2Mbps.
Programmable TX power up to 19.5dBm.
RX sensitivity: -89dBm at 2Mbps on-air data rate.
Fast PLL settling time (30 us) for frequency hopping system.
Built-in AES128 co-processor
AGC (Auto Gain Control) for wide RSSI dynamic range.
AFC (Auto Frequency Compensation) for frequency drift due to temperature.
Low Battery Detector indication.
Easy to use.
Support 3-wire or 4-wire SPI.
Unique Strobe command via SPI.
ONE register setting for new channel frequency.
CRC Error Packet Filtering.
Auto-acknowledgement and auto-resend.
Separated 512Byte TX/RX FIFO.
8-bits RSSI measurement for clear channel indication.
Auto Calibrations.
Auto IF function.
FEC by (7, 4) Hamming code (1 bit error correction / code word).
Easy FIFO / Segment FIFO.
Support FIFO mode frame sync to MCU.
Support direct mode with recovery clock output to MCU.
Frequency band: 2400 ~ 2483.5MHz.
FSK/GFSK modulation.
Sleep current (3 uA).
RX current consumption: 23mA (AGC on).
TX current consumption: 100mA (17dBm).
On chip regulator, support input voltage 3 ~ 3.6 V.
Data rate 2Mbps.
Programmable TX power up to 19.5dBm.
RX sensitivity: -89dBm at 2Mbps on-air data rate.
Fast PLL settling time (30 us) for frequency hopping system.
Built-in AES128 co-processor
AGC (Auto Gain Control) for wide RSSI dynamic range.
AFC (Auto Frequency Compensation) for frequency drift due to temperature.
Low Battery Detector indication.
Easy to use.
Support 3-wire or 4-wire SPI.
Unique Strobe command via SPI.
ONE register setting for new channel frequency.
CRC Error Packet Filtering.
Auto-acknowledgement and auto-resend.
Separated 512Byte TX/RX FIFO.
8-bits RSSI measurement for clear channel indication.
Auto Calibrations.
Auto IF function.
FEC by (7, 4) Hamming code (1 bit error correction / code word).
Easy FIFO / Segment FIFO.
Support FIFO mode frame sync to MCU.
Support direct mode with recovery clock output to MCU.
2.4GHz video baby monitor
2.4GHz video streaming
HiFi quality wireless audio streaming
2400 ~ 2483.5 MHz ISM system
Wireless sensors and building automation
Long range wireless toys
2.4GHz video streaming
HiFi quality wireless audio streaming
2400 ~ 2483.5 MHz ISM system
Wireless sensors and building automation
Long range wireless toys
