首頁 > 產品 > Sub 1GHz 無線通訊晶片 > A7201A
A7201A
產品選擇指南
General Description
A7201A is a very easy-to-use CMOS RF Receiver for sub 1GHz license free ISM band (315/434MHz). It is a FSK/ASK single chip RF receiver with high sensitivity receiver (-110dBm @ 2.4Kbps, 315/433.92MHz ASK/FSK). This device integrates a double balanced image reject mixer, low IF frequency (424KHz) architecture, IF filter, I/Q limiter with RSSI generation, as well as a fully VCO and PLL synthesizer. A7201A's carrier frequency FRF is determined by the frequency of the reference crystal FXTAL. The integer-N PLL synthesizer ensures that each RF value, ranging from 310 MHz to 315.5 MHz and 430 MHz to 438 MHz with PLL steps of 848KHz, can be achieved. This is done by using a crystal as a reference frequency according to: FRF = FXTAL x N / 2R, where N is the PLL feedback divider ratio and R is crystal divider to support 13.5732MHz crystal. Besides, A7201A supports AIF (Auto IF) function, user has no need to consider IF offset between TX and RX, but, use this formula ( FRF = FXTAL x N / 2R ) directly to calculate radio frequency in both TX and RX site.

A7201A supports ASK data rate from 1K to 10Kbps and FSK from 1K to 20Kbps which is determined via external capacitors applied on data filter and data slicer. In FSK modulation, recommend to let input modulated signal be ± 12.5KHz frequency deviation (Fdev). In ASK modulation, Fdev is not a necessary part.

For easy-to-use, A7201A has only two control registers, register 0 and 1. MCU can configure two registers via 3-wire SPI bus. In addition to SPI control mode, A7201A has a special mode called HW control mode. In HW control mode, user just needs to apply pin setting. Then radio control is done (register 0 and register 1 are in default values). No matter HW or SPI control mode, A7201A is very easy to use by a low cost MCU or decoder. Those features are all integrated in a small SSOP 20 pins package.

For packet handling, there is no RX FIFO inside A7201A. Hence, in RX mode, MCU or Decoder can receive the packet (preamble + sync word + payload) from DATA_OUT pin. Be aware that A7201A needs different preamble formats between ASK and FSK in order to get the best RX sensitivity.
 FSK Operating range: VDD=2,2~3,3V. T=-40~+85℃.
 ASK Operating range: VDD=2,2~3,0V. T=-40~+85℃.
 Easy to use
 HW or 3-wire SPI control mode selection.
 HW control mode (no need MCU for radio control, default IFB = mid.).
 Auto calibration.
 Auto start-up sequence, XtalAuto CalibrationPLL RX.
 RX current 9mA (FSK and ASK).
 Shut down mode current 0,5 uA.
 High RX sensitivity (FSK / ASK) down to – 110 dBm at BER<1E-3 (2.4Kbps, 315/433.92MHz).
 Customized digital I/O level (2,0 ~ 3,6V) by VIO pin.
 Fully integrated VCO, on chip loop filter and PLL synthesizer.
 RF range from 290 MHz to 319 MHz with PLL steps of 848KHz by 13.5732MHz Xtal.
 RF range from 420 MHz to 447 MHz with PLL steps of 848KHz by 13.5732MHz Xtal.
 Two balanced Image Reject Mixer and Limiter.
 Integrated IF Filter = mid. (250KHz in ASK, 150KHz in FSK).
 Tunable data filter via external capacitors depending on data rate.
 Tunable data slicer via an external capacitor depending on data rate.
 Support low cost Xtal (13.5732MHz with ± 50ppm stability).
 Very few external components: No need external IF/SAW filters.
 Analog RSSI output.
Remote Control.
Wireless Toys.
Alarm and Security System.
RKE (Remote Keyless Entry).
Smart Energy Management.
Garage Door Opener.
AMR (Auto Meter Reading)
Home Automation.
Datasheet
Application Note
Reference circuit design (Module)
Reference code
Evaluation kit (EK)
Development Kit (DK)
Production test tool
*Please contact the agents or sales for more details