 |
|
首頁 > 產品 > 2.4GHz 無線通訊晶片 > A7106
A7106
產品選擇指南
| General Description |
|
A7106 is a high performance and low cost 2.4GHz ISM band wireless transceiver. This device integrates both high sensitivity receiver (- 95dBm @ 500Kbps) and high efficiency power amplifier (up to 1dBm). In low data rate application, A7106 has special strength for long LOS (line-of-sight) distance because of its ultra high sensitivity (-107 dBm @ 2Kbps, - 104 dBm @ 25Kbps) with no requirement of external LNA or PA. Based on Data Rate Register (0x0E), user can configure on-air data rates from 2Kbps to 500Kbps. A7106 supports fast settling time (130 us) for frequency hopping system. For packet handling, A7106 has built-in separated 64-bytes TX/RX FIFO (could be extended to 256 bytes) for data buffering and burst transmission, CRC for error detection, FEC for 1-bit data correction per code word, RSSI for clear channel assessment, data whitening for data encryption / decryption, the internal RC oscillator for WOR (Wake-On-RX) to support periodically wake up from sleep and listen (auto-enter RX mode) for incoming packets without MCU interaction. Those functions are very easy to use while developing a wireless system. All features are integrated in a small QFN 4X4 20 pins package. A7106’s control registers can be easily accessed via 3-wire or 4-wire SPI bus. For power saving, A7106 supports sleep mode, idle mode, standby mode. For easy-to-use, A7106 has an unique SPI command set called Strobe command that are used to control internal state machine. Based on Strobe commands via SPI bus, MCU can control everything from power saving, TX delivery, RX receiving, channel monitoring, frequency hopping to auto calibrations. In addition, A7106 supports two general purpose I/O pins, GIO1 and GIO2, to inform MCU its status so that MCU could use either polling or interrupt scheme to do radio control. Hence, it is very easy to monitor radio transmission between MCU and A7106 because of its digital interface. |
Small size (QFN4 X4, 20 pins).
Frequency band: 2400 ~ 2483.5MHz.
FSK or GFSK modulation
Low current consumption: RX 16mA, TX 20mA (at 0dBm output power).
Low sleep current (1.5 uA).
On chip regulator, support input voltage 2.0 ~ 3.6 V.
Programmable data rate from 2Kbps to 500Kbps.
Programmable TX power level from – 20 dBm to 1 dBm.
Ultra High sensitivity:
-95dBm at 500Kbps on-air data rate.
-97dBm at 250Kbps on-air data rate
-104dBm at 25Kbps on-air data rate
-107dBm at 2Kbps on-air data rate
Fast settling time (130 us) synthesizer for frequency hopping system.
Built-in Battery Detector.
Support low cost crystal (6 / 8 /12 / 16 / 20 / 24MHz).
Support crystal sharing, (1 / 2 / 4 / 8MHz) to MCU.
Auto Frequency Compensation
Easy to use.
Support 3-wire or 4-wire SPI.
Unique Strobe command via SPI.
ONE register setting for new channel frequency.
8-bits Digital RSSI for clear channel indication.
Fast exchange mode during TRX role switching.
Auto RSSI measurement.
Auto Calibrations.
Auto IF function.
Auto CRC Check.
Auto FEC by (7, 4) Hamming code (1 bit error correction / code word).
Data Whitening for encryption and decryption.
Separated 64 bytes RX and TX FIFO.
Easy FIFO / Segment FIFO / FIFO Extension (up to 256 bytes).
Support direct mode with recovery clock output to MCU.
Support direct mode with frame sync signal to MCU.
Support WOR (Wake-On-RX) to periodically wake up from sleep to RX mode.
Frequency band: 2400 ~ 2483.5MHz.
FSK or GFSK modulation
Low current consumption: RX 16mA, TX 20mA (at 0dBm output power).
Low sleep current (1.5 uA).
On chip regulator, support input voltage 2.0 ~ 3.6 V.
Programmable data rate from 2Kbps to 500Kbps.
Programmable TX power level from – 20 dBm to 1 dBm.
Ultra High sensitivity:
-95dBm at 500Kbps on-air data rate.
-97dBm at 250Kbps on-air data rate
-104dBm at 25Kbps on-air data rate
-107dBm at 2Kbps on-air data rate
Fast settling time (130 us) synthesizer for frequency hopping system.
Built-in Battery Detector.
Support low cost crystal (6 / 8 /12 / 16 / 20 / 24MHz).
Support crystal sharing, (1 / 2 / 4 / 8MHz) to MCU.
Auto Frequency Compensation
Easy to use.
Support 3-wire or 4-wire SPI.
Unique Strobe command via SPI.
ONE register setting for new channel frequency.
8-bits Digital RSSI for clear channel indication.
Fast exchange mode during TRX role switching.
Auto RSSI measurement.
Auto Calibrations.
Auto IF function.
Auto CRC Check.
Auto FEC by (7, 4) Hamming code (1 bit error correction / code word).
Data Whitening for encryption and decryption.
Separated 64 bytes RX and TX FIFO.
Easy FIFO / Segment FIFO / FIFO Extension (up to 256 bytes).
Support direct mode with recovery clock output to MCU.
Support direct mode with frame sync signal to MCU.
Support WOR (Wake-On-RX) to periodically wake up from sleep to RX mode.
Wireless keyboard and mice
Remote control
Helicopter and airplane radio controller
2400 ~ 2483.5 MHz ISM system
Wireless metering and building automation
Wireless toys and game controllers
Remote control
Helicopter and airplane radio controller
2400 ~ 2483.5 MHz ISM system
Wireless metering and building automation
Wireless toys and game controllers
Datasheet
Application Note
Reference circuit design (Module)
Reference code
Evaluation kit (EK)
Development Kit (DK)
Production test tool
*Please contact the agents or sales for more details
Application Note
Reference circuit design (Module)
Reference code
Evaluation kit (EK)
Development Kit (DK)
Production test tool
*Please contact the agents or sales for more details
